ICP DASのCANコンバータは2つ以上の通信インターフェースの物理的なカップリングを構築するのに使用されて、複合ネットワーク構造を実装することができるインフラストラクチャコンポーネントです。必要なCANコンバーターを選択することでCANとCOM、USB、イーサネットインターフェイス間でデータ変換するのに使用される。ユーザは、容易にマルチインタフェースの間のデータ交換とトランスミッションを制御して、統合できます。
CAN BUSファイバーコンバーターセレクションガイド
Model Name I-2533CS I-2533CS-60 I-2533CS-A
I-2533CS-B

*note1
I-2533 I-2532
Pictures
CAN Interface
Module Type
Baud Rate (bps) 10 k ~ 1 M and user-defined 10 k ~ 1 M and user-defined 10 k ~ 1 M and user-defined 10 k ~ 1 M and user-defined 10 k ~ 500 k
CAN Filter Yes Yes Yes Yes No
120Ω Terminator Resistor Built-in Built-in Built-in Built-in Built-in
Isolation 3000 VDC for DC-to-DC, 2500 Vrms for photo-couple
Specification ISO 11898-2, CAN 2.0A and CAN 2.0B
Propagation Delay 190μs *note2 190μs *note2 190μs *note2 250μs *note2 < 120 ns
Fiber Interface
Type SC Duplex type ;
Single mode ;
100Base-FX;
SC type ;
Single mode ;
100Base-FX;
ST (Multi-mode) ST (Multi-mode)
Wave Length (nm) 1310 TX: 1310, RX: 1550 for I-2533CS-A
TX: 1550, RX: 1310 for I-2533CS-B
850 850
Fiber Cable (μm) 8.3/125, 8.7/125, 9/125 or 10/125 8.3/125, 8.7/125, 9/125 or 10/125 8.3/125, 8.7/125, 9/125 or 10/125 50 / 125, 62.5 / 125, 100 / 140 62.5 / 125
Max. Fiber Distance (km) 30 km 60 km 15 km 2 km 1.4 km
Misc.
Topology One-to-One
One-to-Many
One-to-One
One-to-Many
One-to-One
One-to-Many
One-to-One One-to-One
Work with Fiber Switch Yes Yes Yes No No
Extend CAN bus Distance Yes Yes Yes Yes No
Repeat CAN bus signal Yes Yes Yes Yes No
Integrate two different networks Yes Yes Yes Yes No
*note1
The I-2533CS-A と I-2533CS-B はCANアプリケーションにおいてペアで使用しなければならない。
*note2
 伝播遅延はCAN BusボーレートとCANメッセージ・フォーマットに依存します。この値は、1MbpsのCANボーレートを使用することでテストされました。
CAN BUSリピーターセレクションガイド
Module Name I-7531 I-7532 I-2534 I-5534-M
Pictures
CAN Interface
Module Type
Connector Screwed terminal block Screwed terminal block Screwed terminal block 9-pin male D-Sub
Transceiver None NXP 82C250 NXP TJA1042 NXP TJA1042
Channel number 2 2 4 4
Baud Rate (bps) 5 k ~ 800 k 5k ~ 1M bps and user-defined 5k ~ 1M bps and user-defined 5k ~ 1M bps and user-defined
CAN Filter No Yes Yes Yes
Isolation 3000 VDC for DC-to-DC, 2500 Vrms for photo-couple
120Ω Terminator Resistor Built-in Built-in Built-in Built-in
Propagation Delay 200 ns 134 us ~ 30 ms
*note1
240 us ~ 1360 us
*note1
240 us ~ 1360 us
*note1
Misc.
Extend CAN bus Distance No Yes Yes Yes
Repeat CAN bus signal Yes Yes Yes Yes
Integrate two CAN networks at different baud rate No Yes Yes Yes
*note1
伝播遅延はCAN BusボーレートとCANメッセージ・フォーマットに依存します。
最小の遅れは、11ビットのIDと8バイトのデータ@1Mbpsです。
最大の遅れは、29ビットのIDと8バイトのデータ@5kbpsです。
CAN BUSコンバーターセレクションガイド
CANからCOMコンバーターシリーズ製品
Module Name I-7530 I-7530T tM-7530 I-7530A I-7530A-MR I-7530-FT
Pictures RS-232/CAN bus converter RS-232/CAN bus converter RS-232/CAN bus converter Intelligent RS-232/485/422 to CAN bus Converter Intelligent RS-232/485/422 to CAN bus Converter RS-232/CAN bus converter
CAN Interface
CAN Specification ISO-11898-2 ISO-11898-2 ISO-11898-2 ISO-11898-2 ISO-11898-2 ISO-11898-3
CAN Transceiver NXP 82C250 NXP TJA1042 NXP TJA1042 NXP 82C250 NXP 82C250 AMIS 41682
Baud Rate (bps) 10k ~ 1M bps 10k ~ 1M bps 10k ~ 1M bps and user-defined 10k ~ 1M bps 10k ~ 1M bps and
user-defined
10 k ~ 125 k
CAN Filter Yes Yes Yes Yes Yes Yes
CAN Isolation 3000 VDC for DC-to-DC, 2500Vrms ~ 3750Vrms for photo-couple None
Terminator Resistor Built-in 120Ω Built-in 120Ω None Built-in 120Ω Built-in 120Ω Built-in 1kΩ
Max FPS (@1Mbps) 279 ~ 360 279 ~ 360 426 ~ 552 279 ~ 360 370 ~ 1250 279 ~ 360
CAN FIFO 1000 frames 1000 frames 256 frames 1000 frames 128 frames 1000 frames
UART Interface
UART RS-232 RS-232 RS-232 RS-232 / RS-485 / RS-422
(can't be used simultaneously)
RS-232
Baud Rate (bps) 110 ~ 115200 110 ~ 115200 110 ~ 230400 110 ~ 115200 110 ~ 230400 110 ~ 115200
Connector 9-pin female D-Sub 9-pin female D-Sub 9-pin female D-Sub Screwed terminal block Screwed terminal block 9-pin female D-Sub
UART FIFO 900 frames 900 frames 256 bytes 900 frames 256 bytes 900 frames
Misc.
UART / CAN Conversion Half-Duplex Half-Duplex Full-Duplex Half-Duplex Full-Duplex Half-Duplex
Propagation Delay < 3.5 ms < 3.5 ms < 3.5 ms < 3.5 ms -- < 3.5 ms
UART Transparent Communication One-to-One
One-to-Many
One-to-One
One-to-Many
One-to-One
One-to-Many
One-to-One
One-to-Many
One-to-One
One-to-Many
One-to-One
One-to-Many
Modbus RTU Slave No No No No Modbus RTU Slave No
CANからイーサネット変換シリーズ製品
Module Name I-7540D I-7540D-MTCP I-7540D-WF
Pictures Ethernet to CAN/RS-232/RS-485 bus Converter Ethernet to CAN/RS-232/RS-485 bus Converter Ethernet to CAN/RS-232/RS-485 bus Converter
CAN Interface
CAN Connector Screwed terminal block Screwed terminal block Screwed terminal block
Channel number 1 1 1
CAN Transceiver NXP TJA1042 NXP TJA1042 NXP 82C250
Baud Rate (bps) 10k ~ 1M bps and
user-defined
10k ~ 1M bps and
user-defined
5k ~ 1M bps
CAN Filter Yes Yes Yes
CAN Isolation 1000 VDC for DC-to-DC
2500 Vrms for photo-couple
1000 VDC for DC-to-DC
2500 Vrms for photo-couple
3000 VDC for DC-to-DC
2500 Vrms for photo-couple
Terminator Resistor Built-in 120Ω Built-in 120Ω Built-in 120Ω
Max FPS (@1Mbps) 1852 ~ 2244 2118 ~ 2241 700
CAN FIFO 1000 frames 200 frames 256 frames
Ethernet Interface
Controller 10/100Base-TX Ethernet Controller (Auto-negotiating, Auto_MDIX) Wi-Fi (IEEE 802.11b/g)
Protocol TCP / UDP Socket Modbus TCP Server TCP Socket (Client / Server)
Socket clients 25 24 3
others Support Virtual COM Acts as Modbus RTU slave Infrastructure & Ad-hoc mode
Misc.
CAN Transparent Communication One-to-One
One-to-Many
One-to-One
One-to-Many
One-to-One
One-to-Many
USBからCAN変換器シリーズ製品
Module Name I-7565-H1 I-7565-H2 I-7565
Pictures USB to 1 channel CAN bus converter USB to 1 channel CAN bus converter USB to 1 channel CAN bus converter
CAN Interface
CAN Connector 9-pin male D-Sub Screwed terminal block 9-pin male D-Sub
Channel number 1 2 1
CAN Transceiver NXP 82C250 NXP 82C250 NXP TJA1042
Baud Rate (bps) 5k ~ 1M bps and
user-defined
5k ~ 1M bps and
user-defined
10k ~ 1M bps and
user-defined
CAN Filter Yes Yes Yes
CAN Isolation 3000 VDC for DC-to-DC
2500 Vrms for photo-couple
3000 VDC for DC-to-DC
2500 Vrms for photo-couple
3000 VDC for DC-to-DC
2500 Vrms for photo-couple
Terminator Resistor Built-in 120Ω Built-in 120Ω Built-in 120Ω
Max FPS (@1Mbps) 3000 3000 (Total CAN ports) 279 ~ 360
CAN FIFO 256 frames 128 frames (for each CAN port) 1000 frames
USB Interface
USB Type USB Type B USB Type B USB Type B
USB Speed 12M kbps 12M kbps 110 ~ 921600 bps
Specification USB 1.1 and USB 2.0 USB 1.1 and USB 2.0 USB 1.1 and USB 2.0
USB FIFO 100 frames 100 frames 900 frames
Power supply USB USB USB
Misc.
Send CAN with hardware timer Yes Yes No
Show Error Frame Yes Yes No
Adjustable Bit-Timing Yes Yes No
Supported OS Windows 2K/XP/Vista/7 (32 & 64 bit)/8.x, and Linux
Supported LabVIEW Yes Yes LabVIEW UART driver
Supported InduSoft Yes Yes Yes
CAN BUSゲートウェイセレクションガイド
Module Name ECAN-240
Pictures
CAN Interface
CAN Connector 9-pin D-sub male
CAN Transceiver NXP TJA1042
Channel number 2
Baud Rate (bps) 10k ~ 1M bps and user-defined
CAN Filter Yes
CAN Isolation 3000 VDC for DC-to-DC, 2500 Vrms for photo-couple
Terminator Resistor Built-in 120Ω (Dip-Switch)
Max. FPS (@1Mbps) Modbus: 987~990
Pair Connection: 5700~5800
CAN FIFO 256 frame
Ethernet Interface
Controller 10/100Base-TX Ethernet Controller (Auto-negotiating, Auto_MDIX)
Protocol TCP/UDP Socket, Modbus TCP
Socket clients 8
others Alternative Server/Client Mode
Misc.
CAN
Transparent Communication
One-to-One
One-to-Many
CANバスμPACセレクションガイド
PAC CANスロットモジュール
Module Name I-8120W I-87120
Pictures
CAN Interface
Module Communication Parallel Bus Serial Bus
CAN Connector Screwed terminal block Screwed terminal block
Channel number 1 1
CAN Transceiver NXP 82C250 NXP 82C250
Baud Rate (bps) 10k ~ 1M bps and
user-defined
10k ~ 1M bps and
user-defined
CAN Filter Yes Yes
CAN Isolation 1000 VDC for DC-to-DC
2500 Vrms for photo-couple
1000 VDC for DC-to-DC
2500 Vrms for photo-couple
Terminator Resistor Built-in 120Ω Built-in 120Ω
Supported PACs

CAN バス uPAC リスト
Module Name I-7188XBD-CAN uPAC-7186EXD-CAN uPAC-5001D-CAN1
uPAC-5001D-CAN2
Pictures
Hardware
CPU 80186, 40 MHz or compatible 80186, 80 MHz or compatible 80186, 80 MHz or compatible
SRAM 512 kB 512 kB 512 kB
Flash 512 kB 512 kB 512 kB
MicroSD -- -- Up to 2 GB
EEPROM 2 kB 16 kB 16 kB
NVRAM 31 Bytes (battery backup, data valid up to 10 years)
RTC Provide second, minute, hour, date, day of week, month, year
Ethernet -- 10/100 Base-TX (Auto-negotiating, Auto MDI/MDI-X, LED indicators)
COM 1 RS-232 or RS-485 RS-232 RS-232
COM 2 RS-485 RS-485 RS-485
CAN 1 channel and the other is for bypass 1 channel and the other is for bypass uPAC-5001D-CAN1 : 1 channel
uPAC-5001D-CAN2 : 2 channel
WDT Yes (0.8 second) Yes (0.8 second) Yes (0.08 second)
64-bit Serial No. Yes, for Software Copy Protection Yes, for Software Copy Protection Yes, for Software Copy Protection
Development Tools Turbo C 2.01 , TurboC++ 1.01 , Borland C++ 3.01
CANバス通信ボードセレクションガイド
高性能 CAN カードリスト
Module Name PEX-CAN200i PISO-CAN100U PISO-CAN200U PISO-CAN400U PISO-CAN800U
Pictures



Hardware
PC Bus Interface X1 PCI Express Universal PCI Universal PCI Universal PCI Universal PCI
On-board CPU None None None None None
CAN Interface
Channel number 2 1 2 4 8
CAN Transceiver NXP 82C250 NXP 82C250 NXP 82C250 NXP 82C250 NXP TJA1042
Baud Rate (bps) 10k ~ 1M bps and user-defined
CAN Filter Yes Yes Yes Yes Yes
CAN Isolation 1000 VDC for DC-to-DC; 2500 Vrms for photo-couple
Terminator Resistor Built-in 120Ω Built-in 120Ω Built-in 120Ω Built-in 120Ω Built-in 120Ω
Driver
DLL Library VB 6.0, VC++ 6.0, BCB 6.0, Delphi 4.0, C#.Net, VB.Net
Windows Driver Windows 2K/XP, Win7 and Win 8.x (32-bit/64-bit OS)
Linux Driver Linux 2.6.x ~ 3.2.20
SocketCAN Driver Yes Yes Yes Yes None
RTX Driver Yes Yes Yes Yes None
ActiveX Driver Yes Yes Yes Yes Yes
InduSoft Driver Yes Yes Yes Yes Yes
LabVIEW Driver Yes Yes Yes Yes Yes
OPC Server Yes Yes Yes Yes Yes
VxCAN Driver Yes Yes Yes Yes Yes
Software & Toolkit
VxCAN Utility Yes Yes Yes Yes Yes
CANcheck Yes Yes Yes Yes Yes
高性能 PC-104 CAN カード:
Module Name PCM-CAN100 PCM-CAN200 PCM-CAN200P
Pictures
Hardware
PC Bus Interface PCI-104 PCI-104 PC-104+
On-board CPU None None None
CAN Interface
Channel number 1, and the other for bypass 2 2
CAN Transceiver NXP 82C250 NXP 82C250 NXP 82C250
Baud Rate (bps) 10k ~ 1M bps and user-defined    
CAN Filter Yes Yes Yes
CAN Isolation 1000 VDC for DC-to-DC; 2500 Vrms for photo-couple
Terminator Resistor Built-in 120Ω Built-in 120Ω Built-in 120Ω
Driver
DLL Library VB 6.0, VC++ 6.0, BCB 6.0, Delphi 4.0, C#.Net, VB.Net
Windows Driver Windows 2K/XP, Win7 and Win 8.x (32-bit/64-bit OS)
Linux Driver Linux 2.6.x ~ 3.2.20
SocketCAN Driver Yes Yes Yes
RTX Driver Yes Yes Yes
ActiveX Driver Yes Yes Yes
InduSoft Driver Yes Yes Yes
LabVIEW Driver Yes Yes Yes
OPC Server Yes Yes Yes
VxCAN Driver Yes Yes Yes
Software & Toolkit      
VxCAN Utility Yes Yes Yes
CANcheck Yes Yes Yes
インテリジェント PCI CAN カード
Module Name PISO-CM100U PCM-CM100 PISO-CM200U
Pictures

Hardware
PC Bus Interface Universal PCI PCI-104 Universal PCI
On-board CPU 80186, 80 MHz 80186, 80 MHz 32-bit MCU
On-board OS MiniOS7 MiniOS7 --
On-board Firmware Programable Programable --
Firmware SDK Turbo C 2.01 , TurboC++ 1.01 , Borland C++ 3.01 --
CAN Interface
Channel number 1 1 2
CAN Transceiver NXP 82C250 NXP 82C250 NXP 82C250
Baud Rate (bps) 10k ~ 1M bps and user-defined
CAN Filter Yes Yes Yes
CAN Isolation 1000 VDC for DC-to-DC; 2500 Vrms for photo-couple 3000 VDC for DC-to-DC;
3000 Vrms for photo-couple
Terminator Resistor Built-in 120Ω Built-in 120Ω Built-in 120Ω
Driver
DLL Library VB 6.0, VC++ 6.0, BCB 6.0, Delphi 4.0, C#.Net, VB.Net C#.Net,VB.Net, VC++.Net
Windows Driver Windows 2K/XP, Win7 and Win 8.x (32-bit/64-bit OS) Windoes XP, Win7/8.1/10
(32-bit/64-bit OS)
InduSoft Driver Yes Yes --
LabVIEW Driver Yes Yes --
CANバスパワーメータ メーター
ICP DAS brings the most powerful, cost-effective, advanced Smart Power Meters PM-3000 series that gives you access to real-time electric usage for three-phase power measurement. With its high accuracy (<0.5%, PF=1 ), the PM-3000 series can be applied to both low voltage primary side and/or medium/high voltage secondary side and enables the users to obtain reliable and accurate energy consumption readings from the monitored equipments in real time under operation. These compact size and cost-effective power meters are equipped with revolutionary wired clip-on CT (various types, support input current up to 300 A). It operates over a wide input voltages range 10 ~ 500 VAC which allows worldwide compatibility. And with 2 channels relay outputs, it can be linked with sirens or lightings for alarm messages. It also supports Modbus RTU, Modbus TCP or CANopen protocols for easy integration. You can use CT's that you currently own with PM-3133P (without CTs) Power Meter. The CT inputs of the PM-3133P can handle a maximum of 333mV of AC current.
特徴
  • True RMS Power Measurements
  • Energy Analysis for 3P4W, 3P3W, 1P3W, 1P2W
  • Current Measurements Up to 300 A with Different CT Ratio
  • Voltage Measurements Up to 500 V
  • Clip-on CT for Easy Installation
  • W Accuracy Better than 0.5% (PF=1)
  • Supports RS-485, Ethernet (PoE) or CANopen Interface
  • Supports Modbus RTU, Modbus TCP or CANopen Protocol
  • Supports 2 Power Relay Output (Form A)
  • Total Harmonic Distortion (THD)
  • IEC 61010-1and EN 61010-1
PCI-104 compatible form factor and provide 2 CAN channels with D-Sub 9-pin connector
PCI-104 compatible form factor and provide 2 CAN channels with D-Sub 9-pin connector
CANバスデータロガー
 CANロガーシリーズデバイス(CAN-Logger100/CAN-Logger200)はCANバスネットワーク上で簡単に素早くデータ収集と処理を助ける1つか2つのCANポートを持った高性能インテリジェントCANバスデータロガーです。CANロガーデバイスの強力なCPUがそれぞれのCANメッセージのために正確なタイムスタンプが提供されそしてCAN Busネットワークの分析と診断に役に立つCANがメッセージを保存するためSDやSDHCタイプフラッシュのような記憶媒体をサポートします。加えてCAN-Logger200の可搬性を高めるためにこのモジュールはCANバスインタフェースのUSBインターフェースかM12コネクタによって動かされます。CAN-ロガーデバイスはWindowsシステム標準のUSB HIDドライバーを使用します。
特徴
・CAN仕様2.0パートAとB互換
・2500 Vrmsフォトカプラー絶縁CAN側
・ISO 11898-2規格に完全互換
・CANバス承認フィルター構成をサポート
・シングルチャンネルで最大CANデータフローは20000 fps
・CANバスボーレートは10 Kbpsから1 Mbpsまでプログラマブル
・USB2.0高速
・CANメッセージ保存用に4から32 GB SDHC タイプフラッシュをサポート
・CAN側に120Ωターミナル抵抗のジャンパー内蔵
・電源はUSBがCANから
・CANポートは3 KV絶縁
・CANメッセージ送受信用に使用出来るコンフィグユーティリティを提供
CAN-Logger100 CAN-Logger200

CANcheck is a powerful software package that can be used to verify the functions of any CAN device.
Feature:

  • Can set the returned CAN discrimination, eliminating the hassle of wading through logs and manually interpreting results.
  • Can be used to operate and diagnose lights, windows, dashboard or other vehicular electronic systems and components.
  • The graphical interface is ready-made and easy to operate.
  • Supports both the single- and multi-function tests. In multi-function testing, the software provide multi-message sending option.
  • Provides the data conversion from the received CAN messages automatically.
  • Supports two trends to display the real-time waveform which comes from the CAN messages.
  • Provides four free-edited mathematic functions to transfer the raw data instantly and automatically.

The virtual CAN is an integrated library and provides common API functions for all CAN converters and CAN PCI boards.
Feature:

  • It can simultaneously access the CAN devices with different hardware interfaces.
  • Each application can apply the same APIs to access the CAN network.
  • Provide the APIs to search the CAN products within the PC.
  • Provide the APIs to access CAN bus through different CAN products.
  • Provide VxCAN Utility to operate easily.

By using the NAPOPC.CAN DA server, the software engineers would develop their control systems by the familiar SCADA toolkit and any other software which supports OPC client functionality.

The tool tests the following functions simply.

  • Two CAN port test to each other
  • Test with other CAN device
  • Test with CANopen Master/Slave
  • Test with DeviceNet Master/Slave
  • Test with J1939 Receiver/Transmitter